I thought I’d write something about how I spin on a supported spindle. I learned a lot from Fleegle’s book about supported spinning, I highly recommend it.
Starting on an empty spindle
An empty spindle shaft is quite slippery and it’s not always easy to start spinning. I take my fiber, unspun, and wrap it a few times round the shaft quite high, perhaps 3–5 cm from the upper tip. Then I flick the spindle in motion, stop, draft and roll on to the shaft. I repeat these steps a few times, until I have a bit of a length. I transfer the spun yarn onto my fiber hand and then, without removing the fiber from the shaft completely, push the starting fiber down to the placement of the permanent cop. I wind on most of the spun thread on the permanent cop, saving a length to spiral up the shaft. And I’m ready to spin!
Spinning continuously with a short draw
When I spin on a supported spindle I spin continuously. This took me a lot of time to learn and I took it step by step.
There are two major parts of this process (well, three actually, but I will get to the third part later on):
- Spinning
- Rolling the spun yarn onto the temporary cop
For these two steps I need to keep the yarn in different angles in relation to the shaft. When spinning, the yarn is kept in a low angle, 5–45°. This way, the yarn is sliding off the tip every turn and the yarn gets spun. When rolling the yarn onto the shaft, the yarn is kept at a 90° angle from the shaft. So in the spinning process I alternate these two tasks and angles.
Apart from the flicking, I don’t touch the spindle. All the support it needs comes from the spinning surface. The spinning hand is controlling the yarn and the fiber hand is controlling the fiber. I make sure I get a good flick to keep the spinning going long and strong.
Let’s get back to the spinning. For a continuous spin I flick the tip with my spinning hand, preferably with three fingers and my thumb.
I do this in a series of movements, not stopping in between: 5–45° Flick, draft, 90° flick, roll on. If I want to do this with park and draft I stop between: 5–45° Flick. Stop. I draft until I reach my desired amount of twist. Stop. 90° flick, roll on.
There are a few tricks to the spinning that you hardly see in regular motion, but in slow motion they are visible: When I draft I turn my fiber hand against the spinning direction, i.e. anti-clockwise for a clockwise spinning. Just briefly to make the drafting easier and to even out bumps. And just at the beginning of the flicking to roll the yarn onto the temporary cop I take charge by rolling less than a quarter of a round in the wrong direction (anti-clockwise).
Spinning continuously with a long draw
The method is basically the same as for a short draw, but with one difference. When I have flicked the spindle for spinning and put my fingers back on the yarn, I repeatedly open and close my spinning hand fingers on the yarn to let the twist go further into the fiber. This gets you a longer draft before the yarn breaks and a more fluffy yarn.
Moving yarn to permanent cop
So, on to step 3. Using the temporary cop is for convenience. I want to be as economical in my movements as possible and enjoy the continuous motion. But sooner or later I have to move the cop town to its permanent place. So I make a butterfly. With my fiber hand I lift the yarn interchangeably with my thumb and pinkie and thus transfer the yarn from the temporary cop to my fiber hand. When all the yarn from the temporary cop is wound on to my hand I transfer it down to the permanent cop. I help the rolling on with the spinning hand by flicking the shaft. I also make sure I make a neat cop. With a sloppy cop there is a risk the end will never be found again if I lose it.
Plying
Usually I don’t ply on my spindles. It takes too much time and is quite boring. But I do it occasionally when I have just a small amount of yarn to ply. So, I made a short video on plying. There’s nothing special about plying on a supported spindle really. I skip the temporary cop in this part of the process, instead I tilt the spindle a little away from the fiber hand and wind the yarn directly on to the permanent cop. In this video I ply from both ends of a center-pull ball. I keep a fiber hand finger between the singles to keep them in order. Then I just ply away.
Fiber is from Swedish finewool sheep. Spindles are from Maine fiber tools and Malcolm Fielding. Spinning bowl also from Malcolm Fielding. Hoody pattern is Kate Davies’ Northmavine Hoody, yarn from Jamieson & Smith.
Happy spinning!
